收藏本站
NXP Semiconductors
PCA9633
4-bit Fm+ I 2 C-bus LED driver
7.4 Active LOW output enable input
The active LOW output enable (OE) pin, allows to enable or disable all the LED outputs at
the same time.
This control signal is only available for the 16-pin version and does not apply to the 8-pin
or 10-pin versions.
? When a LOW level is applied to OE pin, all the LED outputs are enabled and follow the
output state de?ned in the LEDOUT register with the polarity de?ned by INVRT bit
(MODE2 register).
? When a HIGH level is applied to OE pin, all the LED outputs are programmed to the
value that is de?ned by OUTNE[1:0] in the MODE2 register.
Table 16.
LED outputs when OE = 1
OUTNE1
0
0
1
1
OUTNE0
0
1
0
1
LED outputs
0
1 if OUTDRV = 1, high-impedance if OUTDRV = 0
high-impedance
reserved
The OE pin can be used as a synchronization signal to switch on/off several PCA9633
devices at the same time. This requires an external clock reference that provides blinking
period and the duty cycle.
The OE pin can also be used as an external dimming control signal. The frequency of the
external clock must be high enough not to be seen by the human eye, and the duty cycle
value determines the brightness of the LEDs.
Remark: Do not use OE as an external blinking control signal when internal global
blinking is selected (DMBLNK = 1, MODE2 register) since it will result in an unde?ned
blinking pattern. Do not use OE as an external dimming control signal when internal global
dimming is selected (DMBLNK = 0, MODE2 register) since it will result in an unde?ned
dimming pattern.
7.5 Power-on reset
When power is applied to V DD , an internal Power-on reset holds the PCA9633 in a reset
condition until V DD has reached V POR . At this point, the reset condition is released and the
PCA9633 registers and I 2 C-bus state machine are initialized to their default states (all
zeroes) causing all the channels to be deselected. Thereafter, V DD must be lowered below
0.2 V to reset the device.
PCA9633_5
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 25 July 2008
16 of 43
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PCA9634D,118 IC LED DRIVER RGBA 20-SOIC
PCA9635PW/S911,118 IC LED DRIVER RGBA 28-TSSOP
PCA9685PW,118 IC LED DRIVER RGBA 28-TSSOP
PCA9922PW,118 IC LED DRIVER LINEAR 16-TSSOP
PCA9955TW,118 IC LED DRVR CONST CURR
PCF85102C-2P/03,11 IC EEPROM 2KBIT 100KHZ 8DIP
PCF85103C-2T/00,11 IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8570T/F5,512 IC SRAM 2KBIT 100KHZ 8SOIC
相关代理商/技术参数
PCA9633BS-T 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,112 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DEMO 功能描述:开发板和工具包 - 8051 Brd Philips PCA9633 RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
PCA9633DP1,118 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DP1,118-CUT TAPE 制造商:NXP 功能描述:PCA9633 Series 25 mA 5.5 V 1 MHz SMT 8-bit I2C-Bus LED Driver - TSSOP-8
PCA9633DP2,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N